Accessories

On this page (quick links):

Saddle

p19 saddle fig 21 diagram Accessories p19 saddle fig 22 diagram Accessories

Feature:

Used for anchoring tube/conduit (holds down both tube and End Cap)

Material:

Polished steel plating

Notes:

  1. Apply tape to the tube to make a larger diameter if too loose
  2. Select saddle with dimension (A) in fig. 21 larger than the OD of required tube
  3. Also available in stainless steel

Pack: 100 pieces

Model A(mm) B(mm) C(mm) ÆD(mm) Matching Tube
PZ0104 4 15.8 10 4.5 KS-2.2N · KS-2.6N
PZ0106 6 17.8 10 4.5 KS-3N · 3.2N · KS-4N
PZ0108 8 23.0 12 5.5 KS-5N · KS-6N
PZ0110 10 25.0 12 5.5 KS-7N · KS-8N
PZ0112 12 27.0 14 5.5 KS-9N
PZ0114 14 32.7 16 5.5 KS-10N
PZ0115 15 33.7 16 7.5 KS-11N
PZ0116 16 34.9 18 7.5 KS-13N
PZ0118 18 41.4 20 9.0 KS-14N
PZ0120 20 43.4 20 9.0 KS-15N
PZ1122 22 66.0 25 9.0 —
PZ1125 25 70.0 25 9.0 KS-22N
PZ1128 28 78.0 30 10.0 —
PZ1130 30 80.0 30 10.0 KS-25N

Slotted Screw Driver

p19 slotted screwdriver diagram Accessories

Feature:

For use with M2 screws

Model:

D-M2

Hex-Key Wrench

p19 hex key wrench diagram Accessories

Feature:

For use with M2 hex-head lag screws

Model:

DG-M2

Set pin

p19 set pin figs a b and c diagram Accessories

Feature:

For fastening to sensor head, End Cap and Panel Connector

Material:

Raw steel + Stainless Steel Plating

Note: Screw size selected based on screw-type Sensor Head Connector Chart on Page 15, column F

Model Type of the tip Fig
M2 x 1.5L - Slotted screw A
M2 x 2L- Slotted screw B
M2 x 2.5L Hex Head Lag screw C
M2 x 4L Hex Head Lag screw C
M2 x 3L Hex Head Lag screw C

Adhesive

p19 adhesive diagram Accessories p19 bot adhesive 300x200 Accessories

Feature:

Adhesive used to attach connector to tube/conduit

Material:

High Super-5

Notes:

  1. Apply adequate adhesive onto tube and screw on the connector.
  2. Allow at least 5 minutes for the glue to harden before using.
  3. Does not adhere to polyethylene, polypropylene, nylon, polyvinyl chloride (PVC), fluorocarbon resin, or rubber.

Fiber Protector Cutting Tool

p19 fiber protector cutting tool diagram Accessories p19 bot manual cutting tool 300x199 Accessories

Feature:

For use in cutting tubes

Model:

HG-175

Material:

Steel Alloy

Notes:

  1. Hold the cutter at a 90° angle to the tube and cut one pitch width (3~4mm).
  2. Trim around the circumference of the tube as shown in fig 2.

Fiber Protector Electric Cutting Tool

p19 bot electric cutting tool 300x199 Accessories

Features:

  • The tube is cut straight and clean.
  • Maximum cutting diameter 15.8mm
  • Comes with 5 extra blades

Model:

S-2